中文版 | Collection | Feedback | Contact UsHello, welcome toLINYI ZHAORI ELECTRONICS CO.,LTD. Website!

LINYI ZHAORI ELECTRONICS CO.,LTD.

18566180550

Contacts

LINYI ZHAORI ELECTRONICS CO.,LTD.

Contact:Mrs.Alice Dung
Tel:0539-8058588
Mobile:18566180550
Address:4th Floor, A03 building, High - Tech Electronic Industrial Park,TanCheng District,Linyi City,Shandong,China

ZR-130Wlocation:Home > Products

130W Laser Power Supply

发布时间:2017-9-9 15:33:53

130W Laser Power Supply

130w laser power supply adopts high frequency design, top quality IC parts for major parts to ensure high performance and lifetime. 130 W laser power supplies can be used to 100W – 150W  co2 laser tube  for kinds of industrial laser cutting system, very good compatible and high cost performance. 

 

1. The main features of the 130w laser power supply:

 

* Stable performance:

Each power supply have been much more rigorous testing procedures, under full load high temperature (52~55 degrees celsius) 24 hours of aging, to ensure the stability of each power supply.

* Output voltage, current large (AC220V input, the maximum output current up to 40mA, voltage up to 50kv)

* Improve the laser power: 2000mm laser tube and supporting the use of peak laser power can reach 150W, the average power of 130W.

* Circuit design is reasonable, It’s a high-end laser engraving machine, cutting machine the best choice. At the same time, significantly extend the life of the laser tube.

* Good compatibility:

Can adapt to a number of manufacturers of CO2 laser tube, but also has strong adaptability and fast response, engraving, cutting effect of a good advantage.

* Control is simple:

Select high or low level control, the use of TTL-level control of the laser can start and stop. At the same time increase the protection switch, testing is through the external water and ventilation.

Laser power control is simple, you can use 0 ~ 5V analog signal control the size of the laser power, you can also use the PWM (pulse width modulation) signal to be controlled.* Protection function:

Power supply itself has open circuit protection, a good grounding in the case of protection, the power supply to short-term work in the open state, so to avoid the laser tube burst due to the damage caused by laser power supply, thereby enhancing the laser power supply of life.

* Special Features: (optional addition)

Power users do not need to open the shell, you can simply determine the laser power is working to distinguish between the failure of laser tube 

 

2.Specifications: 


Model

Parameters

130W Laser power

Input

Input Voltage

AC220V±10% (Need  AC110V products, ordering need indicate)

AC frequency

47 - 440HZ

Cold-state Surge Current

≤60A(AC220V input)

≤30A(AC110V input)

Leakage current

≤0.7mA(AC220V input) ≤0.4mA(AC110V input)

Output

Maximum output voltage

 

DC50KV

Maximum output current

DC40mA(depending on the laser tubes of different manufacturers)

Efficiency

≥90%( Full load)

Response speed

≤ 1ms

Control Interface

TTL multilevel switching control, effective level can be high and low   selection (see control wiring diagram)

 

Insulation

                 Input--output

AC 1500V 1 minutes ≤10 mA

                 Input--shell

AC 1500V 1 minutes ≤10 mA

                 Output--shell

Connection

            Insulation Resistance

≥50MΩ(DC500V)

Environmental
  Requested

 

           Working temperature

-10 - 50

Storage of temperature 

-20 - 75

Relative Humidity

Maximum 85% RH (non-condensing)

 

Altitude

 

100,000 feet of work 200,000 feet of storage, does not work

Cooling methods

Forced air cooling (fan cooling)

 

Dimensions (L*W*H)

350mm*235mm*97mm







  


 


上一篇:{aspcms:prevtitle}

下一篇:没有了!

Related products